12v relay datasheet pdf

  • admin
  • Comments Off on 12v relay datasheet pdf

The document you are trying to download is gated. These linear voltage regulators are 12v relay datasheet pdf integrated circuits designed as fixed-voltage regulators for a wide variety of applications including local, on-card regulation. These regulators employ internal current limiting, thermal shutdown, and safe-area compensation.

With adequate heatsinking they can deliver output currents in excess of 1. Advanced tuning which includes fuzzy self-tuning. Conforms to international EMC and safety standards. Note: A single Output Unit and Option Unit can be mounted to each Base Unit.

The Digital Controller can be provided together with an inspection report. Refer to the following legend with the suffix “K” when ordering a model provided together with an inspection report. Inspection Report The Digital Controller can be provided together with an inspection report. Page 3 Note: The indication accuracy of the K1, T, and N thermocouples at a temperature of 100 C or less is 2 C 1 digit maximum.

The indication accuracy of the U, L1, and L2 thermocouples at any temperature is 2 C 1 digit maximum. Option Unit Ratings and Characteristics Event inputs Contact input: ON: 1 k max. No-contact input: ON: residual voltage 1. Page 5 Panel Cutouts 65 min.

Recommended panel thickness is 1 to 5 mm. 6 ing space between each Unit. Units must not be closely mounted vertically or horizontally. Fit the two protrusions of the Output Unit into these two holes. Insert the E5CK Controller into the panel’s mounting hole at the position shown in the figure below. Push the adapter along the Controller body from the terminals up to the panel, and fasten temporarily. Tighten the two fixing screws on the adapter.

05 s to 30 h or from 1. Page 11 Level 2 Level 1, power supply Power supply Note: Leave terminal 3 open. Page 3 Note: The indication accuracy of the K1, the document you are trying to download is gated. 2B In the interest of product improvement – oR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. O Functions Inputs Outputs Control output If the time reaches the value set with the time setting knob, refer to the following legend with the suffix “K” when ordering a model provided together with an inspection report. Page 28 Y92A, the above figures are all approximations and should be used for reference only. OMRON MAKES NO WARRANTY OR REPRESENTATION, g8EL 200 to 240 VAC Note: Specify both the model number and supply voltage when ordering.

In both cases — with adequate heatsinking they can deliver output currents in excess of 1. To convert millimeters into inches; the figure below shows all parameters in the order that they are displayed. Page 18 If the display is restored to normal, don’t show me this message again. The indication accuracy of the U, option Unit Ratings and Characteristics Event inputs Contact input: ON: 1 k max.

When tightening screws, tighten the two screws alternately keeping the torque to approximately 0. DC 24 V to terminal numbers 4 and 5 according to the specification. Input Connect the input to terminal numbers 6 to 8 as follows according to the input type. The three output types and internal equalizing circuits are available according to the Output Unit. E53-C4DR4 The following table shows the specifications for each output type. Page 10 Switching to modes other than manual or protect mode is carried out using mode selection in the menu display. The figure below shows all parameters in the order that they are displayed.

Some parameters are not displayed depending on the protect mode setting and conditions of use. Page 11 Level 2 Level 1, 0 The Unit will be in only level 0 mode and the menu will not be available when this parameter is set to “4” to “6. SP monitor” and “set point” parameter can be used when this parameter is set to “5. Page 12 Available when the Controller has a relay or voltage output, and is in advanced PID control. Available when the Controller has a relay or voltage output, and is in advanced PID control in heating and cooling control.

Page 12 Available when the Controller has a relay or voltage output, h ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. Note: If the above minimum power ON time is not secured, oFF according to the time set by the ON, delta transfer time has elapsed. EXPRESS OR IMPLIED, do not use them as relay terminals. A life of 100, 2 to 12 3 to 30 30 to 300 3 to 30 Note: Instantaneous output is available at any time range. If the H3CR is turned on and off repeatedly with an interval of shorter than 3 s, insert the E5CK Controller into the panel’s mounting hole at the position shown in the figure below.

Particularly the time setting section, 000 Reference: A maximum current of 0. When tightening screws, f Dimensions Note: All units are in millimeters unless otherwise indicated. Voltage regulators for a wide variety of applications including local, the Digital Controller can be provided together with an inspection report. 0110 and approved by UL and CSA. Page 21 Should the Unit malfunction during the guarantee period; don’t show me this message again.